GRC构件是一种装饰材料，可以以自由的形式满足设计师各种个性形式的要求，因此受到设计师的青睐，当然，安装的规格也是必要的，以下小编将教你如何正确安装
山东GRC构件。
GRC components are decorative materials that can meet the requirements of designers in various personality forms in free forms, so they are favored by designers. Of course, the specifications for installation are also necessary. The following small series will teach you how to correctly install Shandong GRC components.
正确的安装方法：
Correct installation method:
1.根据图纸在GRC构件安装处放出定位线。
1. Set out the positioning line at the GRC component installation position according to the drawing.
2.然后按照施工图纸的说明安装切割尺寸的GRC构件，切割GRC构件时，如何掌握GRC构件的尺寸，确保线迹的宽度正好。
2. Then install GRC components with cutting size according to the instructions of the construction drawings. When cutting GRC components, how to master the size of GRC components? First, ensure that the width of the stitches is just.
3.粘贴GRC构件时，网眼布可以折叠，也可以直接粘贴。使用性能良好的粘结砂浆，可用薄层密实的方法将砂浆从GRC构件中强制挤出，粘接处用粘接剂固定，宽度小于3mm，保持粘接处牢固清洁。
3. When pasting GRC components, the mesh cloth can be folded or pasted directly. Use bonding mortar with good performance. The mortar can be forced out of GRC components by thin-layer compaction. The bonding part is fixed with adhesive with a width of less than 3mm. Keep the bonding part firm and clean.
4.安装山东GRC构件，先测量构件的尺寸，现在试着用平地拼接，构件之间的间隙小于3mm时，用性能良好的粘结砂浆粘结，注意粘结砂浆的均匀分布。
4. When installing Shandong GRC components, measure the size of the components first, and then try to splice them with flat ground. When the gap between components is less than 3mm, use bonding mortar with good performance to bond, and pay attention to the uniform distribution of bonding mortar.
5.检查拼接好的GRC构件，可用砂纸打磨接缝粘结砂浆。粘结砂浆干燥后，可以使用GRC构件的抗裂橡胶进一步粘结。
5. Check the spliced GRC components and grind the joint bonding mortar with sand paper. After the bonding mortar is dried, the crack resistant rubber of GRC components can be used for further bonding.
安装的质量标准：
Quality standards for installation:
1、构件安装要求横平竖直，整体在线，图案完整，曲线光滑，构件表面没有污染，无缺陷。
1. The components shall be installed horizontally and vertically, online as a whole, with complete patterns, smooth curves, and free of pollution and defects on the component surface.
2、正确找好构件的安装节点，防止因预埋件错位导致构件扭曲，长期产生安装应力和变形。
2. Correctly locate the installation node of the component to prevent the component from twisting due to the dislocation of embedded parts, which will cause long-term installation stress and deformation.
3、构件连接点连接无泄漏，请拧紧螺栓后再拧紧。
3. There is no leakage at the connection points of components. Please tighten the bolts before tightening.
4、构件接缝光滑，接缝小于10毫米。
4. The joints of components shall be smooth and less than 10mm.
5、纵向构件请勿使上部构件与底部构件重叠，但是，各部件请单独安装在墙上。
5. Do not overlap the upper member and the bottom member of the longitudinal member, but install each component on the wall separately.
6、构件安装后，需要自上而下将表面灰尘、污物清扫干净，吊钩间隙应牢固平整。
6. After the components are installed, the surface dust and dirt shall be cleaned from top to bottom, and the hook gap shall be firm and flat.
The above are the installation methods and installation quality standards introduced by GRC component manufacturers, which can resist damage, deformation and cracking of the external environment, and should be operated according to the correct installation methods. More precautions come to our website http://www.aswjc.com consulting service
